Replacement 1/2' Insert
Click here for more information...
£3.27 ex VAT
£3.92 inc VAT
£3.92 inc VAT
Router Table Stand
Ready-to-assemble stands for the Veritas Router Table Top. While the router table top includes instructions to make a stand, these are ready to go. Table stand is made from 3/4' birch plywood and uses a rigid truss-rod construction.
Click here for more information...
£48.20 ex VAT
£57.84 inc VAT
£57.84 inc VAT
Router Floor Stand
Ready-to-assemble stands for the Veritas Router Table Top. While the router table top includes instructions to make a stand, these are ready to go. Table stand is made from 3/4' birch plywood and uses a rigid truss-rod construction.
Click here for more information...
£155.95 ex VAT
£187.14 inc VAT
£187.14 inc VAT
Router Fence
A straight, rigid, easily adjusted fence that locks perpendicular and allows for good chip escape. Nesting extrusions are the heart of the system. Top rail is a single 28' long piece to maintain rigidity. Lower rail is split for adjustable openings up to 8'.
Click here for more information...
£111.52 ex VAT
£133.82 inc VAT
£133.82 inc VAT
Set Of 3 Jointing Shims
Makes jointing easy. Use a straight bit in the router, set it for 0.010' to 0.060' of cut (easily done with the fence micro-adjust), and then install the matching thickness of shims behind the outfeed sub-fence. Shims are color coded for thickness. Micro-adjust substitutes for an adjustable infeed table and shims provide an adjustable outfeed.
Click here for more information...
£5.00 ex VAT
£6.00 inc VAT
£6.00 inc VAT
Position Stops - Per Pair
Particularly useful for accurately reinstalling the fence on the Veritas Router Table Top in a pre-set location if it had to be removed for any reason. Before removing the fence, tighten the stops next to it at either end. Reinstall in the same position against the stops.
Click here for more information...
£8.68 ex VAT
£10.42 inc VAT
£10.42 inc VAT
Dust Chute
Designed for use with any shop vacuum system. 3' head clamps firmly to any steel surface. Four rare-earth magnets hold it with 40 lb of force. Usable on drill tables, lathes, or other power tools with steel surfaces, such as the Veritas Router Table Top.
Click here for more information...
£19.81 ex VAT
£23.77 inc VAT
£23.77 inc VAT
Fence Stop
Stop fits in the T-slots of the Veritas Router Fence and Right-Angle Sled. Used for many routing jobs to precisely stop a cut. Set it approximately and then fine tune it using the micro-adjust screw. A full turn of the screw is 1/16', 1/2 turn 1/32', 1/4 turn 1/64'.
Click here for more information...
£15.63 ex VAT
£18.76 inc VAT
£18.76 inc VAT
Work Hold Down For Router Fence
A simple, easy way to keep work snugly pressed against the fence and the router table. Ensures safe, accurate cuts. Springs can be set at any pressure as well as a wide range of heights and widths.
Click here for more information...
£25.02 ex VAT
£30.02 inc VAT
£30.02 inc VAT
Fence Mount Safety
Versatile and easy to install. Table-mount shield for pilot work can be set at any one of three heights: 5/8', 1' and 1-5/8'. Screws into the two tapped holes in the Veritas Router Table. Fence-mount shield is adjustable for use with or without sub-fences and for bit heights up to 1-3/4'.
Click here for more information...
£8.27 ex VAT
£9.92 inc VAT
£9.92 inc VAT
Table Mount Safety
Versatile and easy to install. Table-mount shield for pilot work can be set at any one of three heights: 5/8', 1' and 1-5/8'. Screws into the two tapped holes in the Veritas Router Table. Fence-mount shield is adjustable for use with or without sub-fences and for bit heights up to 1-3/4'.
Click here for more information...
£8.27 ex VAT
£9.92 inc VAT
£9.92 inc VAT
Router Baseplate
9' router base plate is small enough to leave permanently mounted to the router for freehand routing and easily inserts with the router into a shop-made table. Most router table inserts are made large enough to accommodate the router's handles as it is lowered into the table from the top.
Click here for more information...
£27.68 ex VAT
£33.22 inc VAT
£33.22 inc VAT
Pin Router Arm
Reverses conventional pin routing with the guide pin in the overhead arm and the router mounted under a table for safer operation and for use in a standard router table. Conventional pin routers use a dedicated router suspended from an overhead arm, leaving the rotating bit exposed with a guide pin mounted in the table.
Click here for more information...
£132.05 ex VAT
£158.46 inc VAT
£158.46 inc VAT
